Burks 33GA5-1-1/4-AI-MV Centrifugal Pump, Close Coupled, 60 Hz, Three Phase, 3500 RPM, 1/3 Horsepower, ODP Motor Enclosure, Frame Size 56J, 42 lbs.
Adapter Material
Cast Iron
Capacities (GPM)
100
Casing Material
Cast Iron
Casing Working Pressure
200
Discharge NPT (Inches)
1.25
Heads To (Feet)
130
HP
1/3
Hz
60
Impeller Material
Cast Iron
Impeller Size (Inches)
3.125"
Inlet Pressure (PSI)
100
Material
All Iron
Maximum Operating Temperature
400°F (204°C)
Motor Enclosure Type
ODP - Open Drip Proof Enclosure
Motor Frame Size
56J
Motor Shaft Material
303 Stainless Steel
Phase
Three Phase
Shaft Seal Material
Viton®
Speed (RPM)
3500
Suction NPT (Inches)
1.5
Voltage
208-230/460
GA5-1-1/4 Series Information
General Description
Burks GA5-1-1/4 Series - Centrifugal Pump, Close Coupled
Materials of Construction
Adapter - All Iron: Cast Iron, Bronze Fitted: Cast Iron, All Bronze: Bronze, Noryl Fitted: Cast Iron Casing - All Iron: Cast Iron, Bronze Fitted: Cast Iron, All Bronze: Bronze, Noryl Fitted: Cast Iron Shaft: #303 Stainless Steel. Impeller - All Iron: Cast Iron, Bronze Fitted: Bronze, All Bronze: Bronze, Noryl Fitted: Glass Filled Noryl Shaft Seal: Carbon Ceramic SS Buna-N
Motors
Standard pump motors are of open drip proof (ODP) construction and are rated with jet pump service factors for continuous duty operation. Motors are 56 frame size with NEMA standard mounting flange, one piece threaded stainless steel shaft and ball/ball bearing construction.
Four Position Casing
Discharge can be located in any of four positions. Casing is close grain iron of 30,000 psi minimum tensile strength. Back pull-out design eliminates the need to disturb piping should the pump ever require service - the casing stays in the line.
NORYL® Impeller
Of the latest hydraulic design for maximum efficiency, impeller has molded in brass insert threaded onto stainless steel motor shaft. *Noryl® Impeller is not designed for use with hydrocarbons.
Mechanical Shaft Seal Information
Standard self-adjusting shaft seal for temperatures to 225°F (107°C) and pressures to 150 psi (1034 kpa). Ceramic seat and carbon seal face for long trouble-free service. Special seals are available for higher temperatures and fluids other than water.
Factory Tested
After careful assembly and inspection, EVERY pump is factory tested and meets Hydraulic Institute standards.
Motor Information
60 Hz - 3500 RPM - ODP Single Phase: 1/3 thru 2 Hp. - 115/230 Volt 3 Hp. - 230 Volt only Three Phase: 1/3 thru 3 Hp. - 208-230/460 Volt 50 Hz - 2900 RPM - ODP Single Phase: 110/220 Volt Three Phase: 380 Volt
Overload Protection
All single phase ODP and Totally Enclosed motors have built-in overload protection. All three phase motors and all explosion proof motors must be installed with a magnetic starter which provides full 3-leg protection. Failure to use correct starter and overloads will void motor warranty.
Enclosed Bronze Impeller
Of the latest hydraulic design for maximum effi ciency, impeller is balanced for vibration-free operation and threaded onto stainless steel motor shaft.
Jacketed Seal Cavity
Series GA5-1 & GA5-1 1/4 Pumps are available in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fluids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. To order, add suffix "MJ" to pump catalog number for temperatures to 500°F (260°C).
0 Reviews
Add a Review
You need to sign in to add a review.