Hydromatic Pumps

Hydromatic Model BV40 Series 4/10 HP Cast Iron/Thermoplastic Sewage Pump - Recessed vortex impeller allows pumping of stringy material and reduces clogging. Manual or automatic operation, Two inch solid handling capability for residential wastewater and sewage applications

Hydromatic CLASSIC Smart Battery Backup Systems Model FG-2200, FG-2200C - The Hydromatic Smart Battery Backup Sump Pump System will help protect the basement from water damage by kicking into action during power outages or primary sump pump failures. Most home buyers don’t think about their sump pump, but when the consequences of unexpected pump failures are understood, the solution from Myers will assist them in making the right decision. The CLASSIC version is available in backup-only (FG-2200) or a pre-plumbed primary + backup system (FG-2200C). Both offer remote monitoring, smart charging technology, and dual battery capacity. In addition to the CLASSIC series, the PREMIUM series is available in backup-only (FG-3100RF) or a pre-plumbed primary+backup system (FG-3100RC). Both offer remote monitoring through our Virtual Water Assistant®, smart charging technology, and dual battery capacity.

The Hydromatic HCU Condensate pump units are designed to automatically remove the liquid from an air conditioner evaporative coil and/or a gas condensing warm air furnace. These units are made from a tough ABS plastic so they will resist corrosion and impacts.

Hydromatic Model HE Series High-Head Stainless Steel Effluent Pumps - High-head filtered effluent pumps are designed specifically for high-pressure applications.

Hydromatic HP33 & HP50 Submersible Cast Iron Sump Pumps - Featuring a vortex impeller that provides solids handling capability up to1/2”. Available in 1/3 HP, 115 volt single phase, 60 Hz and 1/2 HP, 115 volt single phase, 60 Hz. Pump discharge is 1-1/2” NPT . 2-pole float switch for minimum 10” diameter sumps. Also available in manual configuration

Hydromatic Model HPUSP125 Under-Sink Utility Pump - Designed to be used with a sink where gravity drain line is not available. Fully automatic operation, Complete compact system, Designed to be used with a sink where gravity drain line is not available. Up to 40 gpm with 14’ head, Easy to install, Eliminates the need for traps, vents and costly labor, Quiet, trouble-free operation easily mounts beneath your sink

Hydromatic Pump Model HS33PT1, HS50PT1 and HS33PV1, HS50PV1 Submersible Thermoplastic Sump Pump, 1/3 and 1/2 HP - Versatile, long-life basement sump pump also appropriate for many light-duty dewatering jobs. Designed for drain water removal or permanent applications with small amounts of debris. Available in 1/3 or 1/2 HP and your choice of vertical or tethered float switch.

Hydromatic Pump Model HS33PT1, HS50PT1 and HS33PV1, HS50PV1 Submersible Thermoplastic Sump Pump, 1/3 and 1/2 HP - Versatile, long-life basement sump pump also appropriate for many light-duty dewatering jobs. Designed for drain water removal or permanent applications with small amounts of debris. Available in 1/3 or 1/2 HP and your choice of vertical or tethered float switch.

Hydromatic Model HTS33A1, HTS50A1 High-Temperature 1/3 and 1/2 HP Cast Iron Sump Pumps, Submersible sump pump designed for high temperatures up to 194°F.

Applications: Boiler Blow Down Kits, Condensate Pits, Hot Water Sumps

The HTS33 Series Pump is a rugged, submersible, cast iron pump with a non-clog vortex impeller and solids handling capability to 3⁄4”. Unit has 1⁄3 HP, 115 Volt, single-phase motor and 11⁄2” NPT vertical discharge. Available with high temperature float switch.

The HTS50 Series Pump is a rugged, submersible cast iron pump with a non-clog, vortex impeller and features silicon carbide seals. It has solids handling capability to 3⁄4” and is designed to handle liquids to 200°F (93°C). Unit has a 1⁄2 HP single phase motor complete with power cord. 2” NPT vertical discharge is standard.

The Hydromatic HUP4 pump is the ideal solution for a wide range of water drainage and circulation light-duty applications. Shallow flooded areas can be dewatered quickly and efficiently with this powerful and economical utility pump. Submersible Utility Water Removal Pump - 1/6 HP - Ideal for light-duty drainage applications such as flooded basements, flat roofs and swimming pool covers.

The Hydromatic Model HY106 Utility Water Transfer / Removal Pump - Ideal for transferring water,filling tanks and draining shallow flooded areas.

Hydromatic Model HPGR200 - Single-Seal High Head Sewage Pump, 2 HP, Cast Iron, Tethered Switch 1-1/4" Discharge. Single-seal grinder pump is ideal for "high-head" applications involving single-family residences and cottages.

Hydromatic Model OSP Series 1/2 HP Cast Iron / Naval Bronze Effluent Pumps - Continuous duty rated submersible effluent pump. The Hydromatic OSP50 submersible pump is specifically designed to meet the demands of residential sump, elevator pit, septic tank effluent, industrial circulator and transfer tank applications. The 1-1/2 inch NPT discharge pump is available with a powerful 1/2 horsepower motor, in both automatic and manual configurations, and can handle capacities up to 60 gallons per minute and heads to 25 feet.

Applications: Continuous Duty Rated, Septic Tank Effluent, Flood Control Units, Industrial Circulators, Elevator Pits, Basement Sumps

Hydromatic PREMIUM Smart Battery Backup Systems Model FG-3100RF, FG-3100RC - The Hydromatic Smart Battery Backup Sump Pump System will help protect the basement from water damage by kicking into action during power outages or primary sump pump failures. Most home buyers don’t think about their sump pump, but when the consequences of unexpected pump failures are understood, the solution from Myers will assist them in making the right decision. The PREMIUM version is available in backup-only (FG-3100RF) or a pre-plumbed primary+backup system (FG-3100RC). Both offer remote monitoring, smart charging technology, and dual battery capacity. In addition to the PREMIUM series, the CLASSIC series is available as a financial savings option as the FG-2200 and FG-2200C models. The FG-2200 is available with a reliable reed switch rated at up to 10,000,000 cycles for long life. The reliable reed switch design is compact and eliminates the possibility of interference with primary pump switch, unlike using a typical vertical float. The FG-2200C is available with a reliable reed switch and comes standard as a pre-plumbed unit with check valves, a primary pump and secondary pump. The CLASSIC series is not available with Virtual Water Assistant®. Only the PREMIUM series comes standard with the Virtual Water Assistant®.

Hydromatic P Series Pedestal Sump Pump - Basement Sump Draining, Industrial Circulators, Transfer Tanks, Dependable 1/3 HP motor pumps up to 40 GPM at 10’ total dynamic head. Discharge is 1-1/4” N.P.T., Easily adjustable pumping range, Non-corrosive volute/base and impeller, Automatic reset thermal overload protection

Hydromatic Pump Accessories for Rail Systems, Switches, Control Panel Options, Alarm Panels, Junction Boxes and more.

Hydromatic Pump Parts: Diaphragm Switch, Wide Angle Switch, Vertical Float Switch, Mechanical Piggy Back Switch, Kits, O-Rings, Plugs, Screws and more. Every part you need for your Sumbersible Effluent Sewage Sump Pumps

Hydromatic Model S3SD, SB3SD Submersible Sewage Ejector Pump, 3" Discharge -The Hydromatic S3SD and SB3SD sewage pumps are designed to transfer raw sewage with solids as large as 2½". 3" Discharge Submersible Sewage Ejector Pump Models available: S3SD RPM: 1150, S3SD RPM: 1750

Hydromatic Model S3S, SB3S Series 1-1/2 HP - 3 HP Cast Iron Sewage Pumps - Single-seal cast iron submersible sewage pumps.

Hydromatic Model S3WR Submersible Wastewater Vortex Pump - Strong cast iron vortex pumps designed for use with residential raw sewage and light commercial applications.

Hydromatic Model S3W Submersible Cast Iron Solids Handling Wastewater Pumps - Strong cast iron performence designed for residential raw sewage and light commercial applications.

Hydromatic Model S4SD, SB4SD Series Submersible sewage dual seal pumps, 4" Discharge - The Hydromatic S4SD and SB4SD sewage pumps are designed to transfer raw sewage with solids as large as 3". 4"Discharge Submersible Sewage Ejector Pump Models available: S4SD - 1150 RPM, SB4SD - 1750 RPM

Hydromatic Model S4S, SB4S Series Sewage Pump Cast Iron, 4" NPT Discharge, 3.5" Solids Handling (3 HP to 7-1/2 HP) - Single-seal cast iron submersible sewage pumps.

Hydromatic Model SHEF Series Cast Iron Effluent Pumps, 3/10 HP - 1 HP - Cast iron body and oil-filled motor provide superior cooling characteristics for longer pump life. Models include SHEF30, SHEF40, SHEF42, SHEF45, SHEF50 & SHEF100.

The SHEF42 Series Pump is a rugged, submersible cast iron pump with a clog resistant, semi-open impeller and solids handling capability to 3⁄4”. Unit has a 4⁄10 HP single phase motor complete with power cord. 2” NPT vertical discharge is standard.

A full selection of accessories for automatic operation is available, and includes float switches, duplex controllers, simplex controllers, alarms, basins and check valves.

Hydromatic Model SKHD150 High-Head Effluent Pump 1-1/2 HP Cast Iron, 2" NPT Discharge, 3/4" Solids Handling - Generates high heads for bigger drain fields. The Hydromatic SKHD150 submersible pump is specifically designed to meet the demands of septic tank effluent and industrial sump applications that require a “high-head,” dual-sealed pump. The 1-1/2 inch NPT discharge pump is available with a powerful 1-1/2 horsepower motor, which provides maximum starting torque.

Hydromatic Model SKHS Series 1/2 thru 2 HP Cast Iron High Head Sewage Ejectors - Specifically designed to meet the demands of wastewater and sewage handling in residential and commercial building applications.

Hydromatic Model SK Series Cast Iron Submersible Sewage Ejector Pumps, 1/2 HP thru 2 HP Models - Ideal for Commercial and Residential Sewage pumping applications. High Capacity Sump / Septic Tank Effluent

Hydromatic Model SKV Series 4/10 & 1/2 HP Cast Iron Sewage Pumps - Recessed vortex impeller allows pumping of stringy material and reduces clogging.

SKV40 submersible pump is specifically designed to meet the demands of residential wastewater and sewage applications, and the quality standards of the professional plumber. The 2 inch NPT discharge pump is available with a powerful 4/10 HP motor, in both automatic and manual configurations. The SKV40 can handle capacities up to 78 gallons per minute and heads to 19 feet. The SKV40 heavy-duty cast iron and engineered thermoplastic construction provides durability
in rugged applications. The pump’s high-capacity, recessed, vortex impeller is threaded to a stainless steel shaft providing long life in demanding applications. The recessed impeller is capable of passing 2 inch spherical solids and lint.

The Hydromatic SKV50 submersible pump is specifically designed to meet the demands of residential wastewater and sewage applications, and the quality standards of the professional plumber. The 2 inch NPT discharge pump is available with powerful 1/2 HP performance, in both automatic and manual configurations. The SKV50 can handle capacities up to 180 gallons per minute and heads over 20 feet.

Hydromatic Model SPD Series High-Head 1/2 HP Effluent Pumps - Specifically designed to meet the demands of septic tank effluent applications that require a "high-head" dual seal pump. The Hydromatic SPD50H/100H submersible pumps are specifically designed to meet the demands of septic tank effluent applications that require a “high-head”, dual-seal pump. The SPD50H has a powerful 1/2 horsepower motor, while the SPD100H comes with a 1 horsepower motor. Both pumps are standard 2 inch NPT discharge pumps, with 3 inch versions optional, and available in automatic and manual configurations. The SPD50H can handle capacities up to 110 gallons per minute and heads to 50 feet, while the SPD100H handles capacities up to 140 gallons per minute and heads to 63 feet.

Hydromatic Model SP Series 4/10 & 1/2 HP Cast Iron or Naval Bronze Sewage Pumps - Specifically designed to meet the demands of handling wastewater and sewage in residential and commercial building applications.

The SP40 submersible pump is specifically designed to meet the demands of handling wastewater and sewage in residential and commercial building applications. The 2 inch NPT discharge pump is available with a powerful 4/10 horsepower moror, in both automatic and manual configurations; and handles capacities up to 130 gallons per minute and heads up to 26 feet.

The Hydromatic SP50 submersible pump is specifically designed to meet the demands of handling wastewater and sewage in residential and commercial building applications. The 2 inch NPT discharge pump (3 inch discharge optional) is available with a powerful 1/2 horsepower motor, in both automatic and manual configurations; and can handle capacities up to 150 gallons per minute and heads to 29 feet.

The SP50AB features a heavy-duty bronze construction that provides durability in rugged applications, as well as assists in dissipating heat from the motor, for cooler operation. It is also available in an all cast iron model. The pump’s high-capacity, nonclog, bronze impeller which is threaded to a stainless steel shaft provides long life even in demanding applications and is capable of handling up to 1-1/2 inch spherical solids and lint. The SP50AB also features precision, carbonand ceramic-faced mechanical shaft seals that are extensively lapped, providing for a long, leakproof life

Hydromatic Model SPX50 Series Explosion-Proof Effluent Pumps - Rugged, submersible, explosion-proof sump pumps for municipal, commercial and industrial use. HYDROMATIC SPX50 and SPX50H are specifically designed to pump contaminated effluent and water. The SPX 50/SPX 50H is UL and CSA approved (Class 1, Division 1, Group D) to handle a wide variety of pollutants, including gas and oil.

Hydromatic Model SW33, VS33, SD33, SW50, VS50, SD50, 1/3 & 1/2 HP Submersible Cast Iron Sump Pumps, Durable 1/3 and HP - Basement Sumps, Septic Tank Effluent, Industrial Circulators, Transfer Tanks. The Hydromatic® classic submersible pump series is specifically designed to meet the demands of residential sump and septic tank effluent applications. The 1-1/2 inch NPT discharge pump is a 1/3 horsepower, energy-efficient motor, in bothautomatic and manual configurations, and can handle capacities up to 47 gallons per minute and heads to 26 feet. There is also the SD50, SW50 & VS50 verison that is 1/2 HP.

This Hydromatic submersible pump features a heavy-duty cast iron construction that provides the durability for a long service life, as well as assisting in dissipating heat from the motor, for cooler operation. The pump’s anticlog, vortex-design impeller is made from a tough noncorrosive, thermoplastic material, which is capable of providing long, trouble-free service even in demanding applications. The oil-filled motor provides superior cooling characteristics, allowing the motor to run cool and quiet in extended service. This oil-filled design also provides permanent lubrication of the shaft bearings, minimizing maintenance and extending the service life of the pump. In addition, to protect against over- heating, the motor windings contain an automatic reset thermal overload.

Automatic models feature an easily adjustable, wide-angle float, diaphragm pressure switch, or a vertical mechanical float switch, all three switch configurations incorporating a unique “piggyback” plug arrangement. This piggyback design allows for simple conversion to manual operation by simply removing the switch plug and inserting the motor plug directly into the electrical outlet. This feature provides an easy way of periodically cycling the pump to ensure it is operating properly.

Hydromatic Pumps W/D/V A1 Submersible Cast Iron Sump Pumps - Basement Sumps, Septic Tank Effluent, Industrial Circulators, Transfer Tanks. Automatic operation features wide-angle float switch
(W-A1), or Hydromatic’s exclusive pressure diaphragm switch (D-A1) or Hydromatic’s vertical, mechanical float switch (V-A1). All switches feature a piggyback plug-in arrangement that allows for simple conversion to manual operation. Cast iron body and an oil-filled motor provide superior cooling characteristics for longer pump life. Motor windings contain automatic thermal overload protection. Energy efficient .3 HP motor pumps up to 38 GPM at 10’ total dynamic head. Discharge is 1-1/2” N.P.T.