Image shown may not be actual product
Burks ED8M-AB-MV Turbine Pump, Base Mounted, 1750 RPM, ODP Motor Enclosure, 115 lbs.
Burks ED8M-AB-MV Turbine Pump, Base Mounted, 1750 RPM, ODP Motor Enclosure, 115 lbs.
Casing Material | Bronze |
Casing Working Pressure | 200 |
Frame Material | Bronze |
HP | 15 |
Impeller Material | Bronze w/ Monel Blades |
Inlet Pressure (PSI) | 50 |
Material | All Bronze |
Maximum Operating Temperature | 250°F (121°C) |
Motor Enclosure Type | ODP - Open Drip Proof |
Motor Shaft Material | 303 Stainless Steel |
Part Number | ED8MV-AB |
Raceway Material | Bronze |
Shaft Seal Material | Viton |
Speed (RPM) | 1750 |
Strainer Material | Bronze (Brass Screen) |
General Description |
---|
Burks EC & ED Series - Regenerative Turbine Pumps, Base Mounted |
Materials of Construction |
Power Frame - Bronze Fitted: Cast Iron, All Bronze: Bronze Casing - Bronze Fitted: Cast Iron, All Bronze: Bronze Strainer - Bronze Fitted: Cast Iron (Brass Screen), All Bronze: Bronze (Brass Screen) Impeller - Bronze Fitted: Bronze (Monel Blades), All Bronze: Bronze (Monel Blades) Raceway: Bronze Fitted: Bronze, All Bronze: Bronze Shaft: #303 Stainless Shaft Seal: Carbon Ceramic SS Buna-N |
Mechanical Shaft Seal Information |
The leakproof mechanical shaft seal for temperatures to 225°F (107°C), is self-adjusting. A wide variety of mechanical seals are available for handling liquids other than water. |
Factory Tested |
Every pump factory tested for capacity, head and power consumption. |
Jacketed Seal Cavity |
Series EC & ED Pumps are available in a Jacketed Seal Cavity design for pumping hot oil, hot water and heat transfer fl uids in common use in high temperature heating or cooling applications. This feature greatly extends seal life in high temperature applications. To order, add suffix “J” to pump catalog number for temperatures below 400°F (204°C) and add suffix “JK” to pump catalog number for temperatures over 400°F (204°C). Example: EC6MJ. |
Interchangeability |
Interchangeability Chart Catalog No. | Replaces | Catalog No. | Replaces EC4M E16M ED8M E23M EC5M EC17M ED9M E24M EC6M E18M ED10M E25M EC7M E19M ED11M E26M EC8M E20M ED12M E27M EC9M E21M ED14M E29M EC10M E22M |
Power Frames |
Power frames are supplied with grease lubricated ball bearings. Wide bearing spacing provides solid shaft support. Tapped and plugged openings are conveniently located for easy relubrication of power frame. Grease relief holes prevent over-lubrication. |
Impeller Information |
The bronze impeller, with monel metal blades secured in slots in the liquid channel by means of a brazing process, is the only moving part. Annular grooves or sealing rings are machined in the face of the impeller. These grooves are perfectly matched with corresponding grooves in the raceway and intermesh without metal to metal contact to form a labyrinth seal. |
Raceway Information |
The bronze raceway is the mating part to the impeller. Sealing grooves are machined into the face of the raceway to match the impeller sealing grooves reducing water slippage to a minimum, resulting in better efficiencies, while reducing the possibility of vapor bind. |
External Adjustment |
The adjusting screw is located in the power frame on Independent Pumps. A positive pre-load spring pressure is applied to the pump shaft bearing and in turn, is transmitted to the adjusting screw. This controlled pressure eliminates bearing end-play and provides a means for external adjustment of the clearance between the impeller and raceway. The distinct advantage of this exclusive BURKS feature is the positive means provided to establish the initial clearance between the impeller and raceway, plus providing a means for external readjustment to compensate for any possible wear between these parts. The customer benefit of this exclusive feature is the fact that readjustment can be made without disassembling the pump or disturbing the piping. |
Casing Information |
Casing is close grain iron of 30,000 PSI minimum tensile strength. Should the pump require service there’s no need to disturb the piping - the casing stays in the line. |
Self Priming |
Once casing is filled with water - will handle water, air or a mixture of both to high pressure. |
Boiler Feeds
1769 productsCirculation
1769 productsCondensate Return
1769 productsCooling Tower
11343 productsHigh Temperature
1769 productsLiquid Transfer
2494 productsStay tuned for releases of new product reviews and videos on our YouTube channel!
Check our Social Media for new product announcements and exclusive specials for our followers.
0 Reviews
Add a Review
You need to sign in to add a review.